$110.00

DC Booster Pump Assembly (for up to 100GPD membrane RO systems, good for 50GPD, 75GPD too).  Comparable to Aquatec 8800 and 6800 pumps

NOW with BONUS pressure gauge  (so you can tell the boost pressure after the pump)

This water booster pump is to boost the input water pressure.  It is usually used to increase the input water pressure for Reverse Osmosis systems. (boost pressure from 60 to 80 psi)

The Pump assembly includes:  pump, transformer, solenoid valve, pressure switch.  The pump turns-on to produce water into the pressure tank, and then turns off when the pressure tank is full or when storage tank pressure reaches 40 psi.

Benefits of using Booster pump for Reverse osmosis systems

·        For RO systems, an increase in input water pressure means an increase in water production and water purity

·        RO systems will run more efficient, and have less drain water. Since it uses pressure switch and solenoid valve to turn on/off the water input, it can turn-on and turn-off more accurately than the mechanical auto-shut-off valve.

·        If you use large water container or open water tank, you can use float switch or level switch to control the operation of the pump as well.

·        The transformer included in the package is plugged into regular 110V/60HZ electrical outlet.

Specifications:

Booster Pump:
Boost pressure	If input water pressure is about 30 to 40 psi, the pump will boost pressure to about 70 to 80 psi for RO systems
Water open flow	1 liter per minute or 0.26 gallons per minute
Electrical:	24VDC,  0.22Amp
Connection	Inlet and outlet,  3/8" FPT,  or two 3/8"MPT to 1/4 compression fitting are included (connects to 1/4" tubing)
Motor	Permanent Magnet,  24VDC, enclosed
PUMP	Diaphragm pump, 3 chamber, self-priming.  It is able to run dry
Material:  Housing	Nylon
Valves	EPDM
Diaphragm	Santoprene
Fasteners	Stainless Steel
Dimension	diameter = 3.5" , length = 7.5"

 

Solenoid valve
Type	Normally Close (NC)   orifice opens when electrically energized
Electrical:	24VDC, Leads = 20 AWG
Water pressure	0 to 120 psi
Connection:	two ¼”x ¼” fitting included:  connect to ¼” tubing
Mounting	It has two screw holes for mounting
Material:  valve	Plastic valve body, water contacts only plastic and nylon parts
Solenoid	brass outside body, stainless steel internal parts

 

Pressure switch
Type:	Normally closed (NC)  will cut off circuit when water pressure reaches 40 psi
Pressure	Cut off pressure at 40 psi,  maximum inlet pressure 120 psi
Connection	¼” compression ,  connect to ¼” tubing
Material	Polypropylene
Electrical: leads	20 AWG, 14” long
Max:	15A, 250Volts

 

 

Transformer
Input	110V/60Hz
Output	24VDC  1A
Leads	18 AWG, 5 feet

* 752SET, Booster Pump Assembly for RO Water Systems (18 GPD to 100 GPD RO systems) (for larger systems use p/n 773 pump assembly)

* Booster pump assembly includes: booster pump, 24 VDC to 115 VAC 1.2 Amp transformer, solenoid valve, pressure switch, and electric wire.

* This pump assembly is to be used when source water to RO system has water pressure lower than 40 psi.

* The pump will boost and maintain feed water pressure to around 70-80 psi so that maximum efficiency of the RO system can be achieved.

* The pump is quiet, self-prime, can run dry without damage, and it is especially designed for RO systems.

* After installing Pump assembly, the RO system will be controlled electronically by the solenoid valve and pressure switch, so when tank is full or reaches 40 psi, the pump will shut-off and the solenoid valve would turn off the water supply. This is a better system than RO without pump since the pressure switch is much more accurate than the auto-shut-off valve in standard RO.