Log In Log In  |  Checkout   |  6 item(s)
Home
Specials Log InCreate Account Checkout  Shopping Cart6 item(s)
Categories
Aquarium RO+DI Systems
Drinking Water RO Systems
Aeroponics Hydroponics RO System
CounterTop Systems
Whole House Systems
Faucets Water Spout
Replacement Filters & Housings ->
TDS Meters & Flow Meters
Pumps
Valves
Fittings
Accessories
Components
Filter Housing Canister
Information
Frequently Asked Questions FAQ
   -> System and Product Dimension
   -> Booster Pump / Low Pressure:
   -> Booster Pump Setup – Pressure Gauge and adjusting pressure:
   -> Tubing Operating Pressure and Material:
   -> Non Air-Gap Faucet:
   -> Draining water ratio: 1:3:
   -> RO System Knowledge Things You Should Know:
   -> How to install float valve FV14 FV15:
   -> UV BALLAST INFO:
   -> Aquatec CDP6800 wire and tapes:
   -> Water running continuously nonstop drain when tank is full:
   -> Requires drain water! DO NOT block off the drain:
   -> Tips on saving water:
   -> Pressure Gauge rattle sound:
   -> Faucet started dripping constantly:
   -> Fluoride Removal:
   -> Faucet Drill Hole Size:
   -> When to replace filters:
   -> Alkaline System and how it works:
   -> Add Alkaline filter to an existing system:
   -> TDS Calibration:
   -> Third Party Product Warranty Warranty Claims:
   -> Not using the drinking water feature on RD106:
   -> Tank takes long time to fill, troubleshooting:
   -> Not much or Little Water out of RO system:
   -> Leaking Faucet / Dripping faucet:
   -> K5 and RO585 difference:
   -> AR122 and RD102 are not a drinking water system:
   -> Why pumps are wet when they are new:
   -> Permeate pump and waste water:
   -> PH strips is not good:
   -> Pressure Gauge is missing:
   -> Clear Filter Housing Warning Advice:
   -> Unable to open Filter Housing:
   -> K5 Faucet Swap Substitute:
   -> Booster pump to increase pressure:
  Tank installation instruction:
   -> Permeate or Booster Pump Noise:
   -> When to replace filters:
   -> Why install booster pump before 4th stage membrane:
   -> Pressure switch does not shut off pump sometimes:
   -> TDS reading ppm of the filtered water:
   -> Is storage pressuer tank necessay for RO system:
   -> O ring o-rings of Filter Casing Housing not available:
   -> Flow meter display instruction:
   -> Flow meter measurement accuracy:
   -> Air Bubbles in the water:
   -> Whole House System vs RO System:
   -> Booster pump for misting application:
   -> Installation of Auto Shutoff Valve:
   -> DI Filter is leaking or unable to tighten:
   -> Cracked Elbow Fitting:
   -> What is Flow Restrictor in RO Systems?
   -> ESO and TSO:
   -> New Feed Water Adapter
   -> Instruction for Refilling the 215 Inline DI filter
Shipping,Tax,& Returns
Terms & Conditions
Privacy Notice
Warranty
About Us
Product Showcase
Aquarium Photos
Contact Us
Support Manuals

Tank installation instruction:

Tank is already pre-charged at 7 psi, you just need to screw on the tank valve and connect a 1/4" tubing to it.
Remember to put some Teflon tape on thread (about 8 turns) on top of the tank, and then screw on the tank valve (hand tight only), then unscrew the compression nut off the tank valve, then push a 1/4" tubing through the compression nut, then tighten the compression nut to the tank valve (wrench tight).
Continue
Home  |   Specials  |   Log In  |   Create Account  |   Checkout  |   Shopping Cart

Copyright © 2024 Filter Direct Online Store (C)